Slideshow Items

  • industrial oxygen concentrator

Technology

The Oxiti industrial oxygen concentrator uses pressure swing adsorption (PSA) technology. Air holds 3 major gasses, 21% oxygen, 78% nitrogen and 1% argon and an oxygen concentrator removes nitrogen from air.

Acniti uses a high-quality compressor in the oxygen concentrator, the compressor compresses over 100 liters of air per minute. The compressed air feeds into an air-dryer to remove all the moisture and other impurities. After the air-dryer, the air flows into one of the two oxygen sieves. In the sieve, nitrogen molecules stick to zeolite under pressure and oxygen passes through the sieve and flows to a small storage container. When the oxygen sieve saturates, and this happens in a matter of seconds, the solenoid valve system will switch to the second sieve to repeat the process. The first sieve then depressurizes, and the nitrogen purges out of the sieve and the oxygen concentrator. This process is constantly repeated.

Quality components

The oxiti uses quality components from Japanese and American manufactures in a rugged aluminum casing. The quality components ensure a long life and easy maintenance with standard components. A lot of oxygen concentrators developed for the healthcare market are for home use and lack the strength, environmental design, and durability of the industrial oxygen concentrators. The industrial designed concentrators have larger and easy to wash and inlet filters. Another focus point is the air drying after the compressor. Water attracts easily to the zeolite. Once the water attaches to zeolite, the zeolite is no longer able to hold the nitrogen and the sieves need replacement.

The oxygen concentrator unit contains a pressure gauge which enables the user to check the pressure at the inlet of the nanobubble generator, the oxiti supplies a pressure of 70-100 kPa, when higher pressures are required, for dissolving larger quantities of gasses more efficiently please check the oxiti booster.

Oxiti industrial oxygen concentrator

  • 1, 5 and 8 LPM industrial oxygen concentrator
  • High quality Japanese components and assembled in Japan
  • Microprocessor controlled
  • Low operating cost
  • Transportable design
  • Easy to install and maintain

Model

specifications

  • Model nameindustrial oxygencentrator 8 LPM 115V
    Model numberoxiti-08-115
    Spec sheetindustrial oxygencentrator 8 LPM 115V
    AmbientMetricImperial
    Ambient temperature minimum10 ℃50 ℉
    Ambient temperature maximum40 ℃104 ℉
    Relative humidity minimum15 %15 %
    Relative humidity maximum95 %95 %
    GasMetricImperial
    Minimum flow / minute2.0 Liter0.5 Gallon
    Maximum flow / minute8.0 Liter2.1 Gallon
    Minimum flow / hour120 Liter32 Gallon
    Maximum flow / hour480 Liter127 Gallon
    Pressure minimum 70 kPa10 PSI
    Pressure maximum 100 kPa15 PSI
    Gas quality87% to 96% Oxygen
    Gas remarkambient air
    Electrical
    Unit phase Ø voltage1 Ø 115 VAC 60 Hz or 50 Hz
    Unit power consumption605 watts 60 Hz or 480 watts 50 Hz
    Connections
    Gas inlet10 mm push to connect fitting or 3/8" on request
    Dimensions & weightMetricImperial
    Dim. (w) x (d) x (h)460 x 444 x 695 mm18.1 x 17.5 x 27.4 inch
    weight29.9 Kg65.9 lbs.
    Shipping dim. (w)x(d)x(h)60 x 57 x 80 cm24 x 22 x 31 inch
    Shipping weight32.9 Kg73 lbs.
    • Altitude 21 degrees up to 1500 meter (5000 ft) without degradation, contact us for more information regarding 1,500 m to 4,000 m (5,000 - 13,000 ft)
    • Storage temperature from - 20 °C to 60 °C (0°F to 140 °F)
    • unprotected or inadequately ventilated environment or improper control power may cause damage to the oxygen concentrator and is not covered under warranty.
  • Model nameindustrial oxygencentrator 8 LPM 230V
    Model numberoxiti-08-230
    Spec sheetindustrial oxygencentrator 8 LPM 230V
    AmbientMetricImperial
    Ambient temperature minimum10 ℃50 ℉
    Ambient temperature maximum40 ℃104 ℉
    Relative humidity minimum15 %15 %
    Relative humidity maximum95 %95 %
    GasMetricImperial
    Minimum flow / minute2.0 Liter0.5 Gallon
    Maximum flow / minute8.0 Liter2.1 Gallon
    Minimum flow / hour120 Liter32 Gallon
    Maximum flow / hour480 Liter127 Gallon
    Pressure minimum 70 kPa10 PSI
    Pressure maximum 100 kPa15 PSI
    Gas quality87% to 96% Oxygen
    Gas remarkambient air
    Electrical
    Unit phase Ø voltage1 Ø 230 VAC 50 Hz or 60 Hz
    Unit power consumption550 watts
    Connections
    Gas inlet10 mm push to connect fitting or 3/8" on request
    Dimensions & weightMetricImperial
    Dim. (w) x (d) x (h)460 x 444 x 695 mm18.1 x 17.5 x 27.4 inch
    weight29.9 Kg65.9 lbs.
    Shipping dim. (w)x(d)x(h)60 x 57 x 80 cm24 x 22 x 31 inch
    Shipping weight32.9 Kg73 lbs.
  • Model nameindustrial oxygencentrator 5 LPM 115V
    Model numberoxiti-05-115
    Spec sheetindustrial oxygencentrator 5 LPM 115V
    AmbientMetricImperial
    Ambient temperature minimum10 ℃50 ℉
    Ambient temperature maximum40 ℃104 ℉
    Relative humidity minimum15 %15 %
    Relative humidity maximum95 %95 %
    GasMetricImperial
    Minimum flow / minute1.0 Liter0.3 Gallon
    Maximum flow / minute5.0 Liter1.3 Gallon
    Minimum flow / hour60 Liter16 Gallon
    Maximum flow / hour300 Liter79 Gallon
    Pressure minimum 70 kPa10 PSI
    Pressure maximum 100 kPa15 PSI
    Gas quality87% to 96% Oxygen
    Gas remarkambient air
    Electrical
    Unit phase Ø voltage1 Ø 115 VAC 60 Hz or 50 Hz
    Unit power consumption605 watts 60 Hz or 480 watts 50 Hz
    Connections
    Gas inlet10 mm push to connect fitting or 3/8" on request
    Dimensions & weightMetricImperial
    Dim. (w) x (d) x (h)460 x 444 x 695 mm18.1 x 17.5 x 27.4 inch
    weight29.9 Kg65.9 lbs.
    Shipping dim. (w)x(d)x(h)60 x 57 x 80 cm24 x 22 x 31 inch
    Shipping weight32.9 Kg73 lbs.
    • Altitude 21 degrees up to 1500 meter (5000 ft) without degradation, contact us for more information regarding 1,500 m to 4,000 m (5,000 - 13,000 ft)
    • Storage temperature from - 20 °C to 60 °C (0°F to 140 °F)
    • unprotected or inadequately ventilated environment or improper control power may cause damage to the oxygen concentrator and is not covered under warranty.
  • Model nameindustrial oxygencentrator 5 LPM 230V
    Model numberoxiti-05-230
    Spec sheetindustrial oxygencentrator 5 LPM 230V
    AmbientMetricImperial
    Ambient temperature minimum10 ℃50 ℉
    Ambient temperature maximum40 ℃104 ℉
    Relative humidity minimum15 %15 %
    Relative humidity maximum95 %95 %
    GasMetricImperial
    Minimum flow / minute1.0 Liter0.3 Gallon
    Maximum flow / minute5.0 Liter1.3 Gallon
    Minimum flow / hour60 Liter16 Gallon
    Maximum flow / hour300 Liter79 Gallon
    Pressure minimum 70 kPa10 PSI
    Pressure maximum 100 kPa15 PSI
    Gas quality87% to 96% Oxygen
    Gas remarkambient air
    Electrical
    Unit phase Ø voltage1 Ø 230 VAC 50 Hz or 60 Hz
    Unit power consumption495 watts 50 Hz or 640 watts 60 Hz
    Connections
    Gas inlet10 mm push to connect fitting or 3/8" on request
    Dimensions & weightMetricImperial
    Dim. (w) x (d) x (h)460 x 444 x 695 mm18.1 x 17.5 x 27.4 inch
    weight29.9 Kg65.9 lbs.
    Shipping dim. (w)x(d)x(h)60 x 57 x 80 cm24 x 22 x 31 inch
    Shipping weight32.9 Kg73 lbs.
  • Model nameindustrial oxygencentrator 1 LPM 115V 60Hz
    Model numberoxiti-01-115/60
    Spec sheetindustrial oxygencentrator 1 LPM 115V 60Hz
    AmbientMetricImperial
    Ambient temperature minimum10 ℃50 ℉
    Ambient temperature maximum40 ℃104 ℉
    Relative humidity minimum15 %15 %
    Relative humidity maximum95 %95 %
    GasMetricImperial
    Minimum flow / minute0.1 Liter0.0 Gallon
    Maximum flow / minute1.0 Liter0.3 Gallon
    Minimum flow / hour6.0 Liter1.6 Gallon
    Maximum flow / hour60 Liter16 Gallon
    Pressure 75 kPa11 PSI
    Gas quality87% to 96% Oxygen
    Gas remarkambient air
    Electrical
    Unit phase Ø voltage1 Ø 115 VAC 60 Hz
    Unit power consumption135 watts 60 Hz
    Connections
    Gas inlet6 mm push to connect fitting or 1/4" on request
    Dimensions & weightMetricImperial
    Dim. (w) x (d) x (h)270 x 550 x 450 mm10.6 x 21.7 x 17.7 inch
    weight14 Kg30.9 lbs.
    Shipping dim. (w)x(d)x(h)43 x 65 x 48 cm17 x 26 x 19 inch
    Shipping weight16 Kg35 lbs.
    • Altitude 21 degrees up to 1500 meter (5000 ft) without degradation, contact us for more information regarding 1,500 m to 4,000 m (5,000 - 13,000 ft)
    • Storage temperature from - 20 °C to 60 °C (0°F to 140 °F)
    • unprotected or inadequately ventilated environment or improper control power may cause damage to the oxygen concentrator and is not covered under warranty.
  • Model nameindustrial oxygencentrator 1 LPM 220V 50Hz
    Model numberoxiti-01-220/50
    Spec sheetindustrial oxygencentrator 1 LPM 220V 50Hz
    AmbientMetricImperial
    Ambient temperature minimum10 ℃50 ℉
    Ambient temperature maximum40 ℃104 ℉
    Relative humidity minimum15 %15 %
    Relative humidity maximum95 %95 %
    GasMetricImperial
    Minimum flow / minute0.1 Liter0.0 Gallon
    Maximum flow / minute1.0 Liter0.3 Gallon
    Minimum flow / hour6.0 Liter1.6 Gallon
    Maximum flow / hour60 Liter16 Gallon
    Pressure 75 kPa11 PSI
    Gas quality87% to 96% Oxygen
    Gas remarkambient air
    Electrical
    Unit phase Ø voltage1 Ø 220 VAC 50 Hz
    Unit power consumption135 watts 50 Hz
    Connections
    Gas inlet6 mm push to connect fitting or 1/4" on request
    Dimensions & weightMetricImperial
    Dim. (w) x (d) x (h)270 x 550 x 450 mm10.6 x 21.7 x 17.7 inch
    weight14 Kg30.9 lbs.
    Shipping dim. (w)x(d)x(h)43 x 65 x 48 cm17 x 26 x 19 inch
    Shipping weight16 Kg35 lbs.
    • Altitude 21 degrees up to 1500 meter (5000 ft) without degradation, contact us for more information regarding 1,500 m to 4,000 m (5,000 - 13,000 ft)
    • Storage temperature from - 20 °C to 60 °C (0°F to 140 °F)
    • unprotected or inadequately ventilated environment or improper control power may cause damage to the oxygen concentrator and is not covered under warranty.